+86-0371-67989006 
safety procedure for fuel dispense
Recommend Products
Occupational Health & Safety (OHS) in Petrol Stations
Procedures to be followed in the event of spillage, and particularly the spillage of flammable liquid on clothing. Risks when draining fuel tanks, particularly over inspection pits. Precautions for hot work on vehicle fuel tanks. Safety of electrical equipment used in
ABOVEGROUND PETROLEUM STORAGE TANKS
Gasoline Dispensing Facilities (GDF). A Gasoline Dispensing Facility is defined as any stationary facility which dispenses gasoline into the fuel tank of a motor vehicle, motor vehicle engine, non road vehicle, or non road engine, including a non road vehicle or non road engine used solely for competition; including, but not limited to,
Safe Operating Procedure Environmental Health & Safety
use of hand pumps. “Transfer” does not include pumping fuel from a standard dispensing pump into a motorized vehicle. Generic versions of these inspection forms are available in the appendix of this SOP. Inspection forms specific to each SPCC Plan are found in those plans. The forms are
Handbook for Handling, Storing, and Dispensing E85 and
Most transportation fuel sold in the United States is manufactured to ASTM specifications. ASTM Interna tional is a voluntary consensus standards organization that creates and maintains fuel quality specifications established by committees composed of vehicle and engine manufacturers, fuel system equipment manufac
Electrical Safety for Motor Fuel Dispensing Facilities
Meeting the NEC disconnect requirements at motor fuel dispensing facilities provides necessary safety for personnel and station equipment during maintenance and service activities. The current requirements in NEC and emphasize that the system low voltage circuits are included and must be disconnected as well.
MSU Standard Operating Procedures Vehicle and
MSU Standard Operating Procedures Vehicle and Equipment Fueling Introduction and Purpose Vehicle and equipment fueling procedures and practices are designed to minimize pollution of surface or ground waters. Understanding the procedures for delivering fuel into vehicles, mobile fuel tanks, and storage tanks is critical for this purpose. Safety is
STRATEGIC OUTCOMES PRACTICE TECHNICAL ADVISORY
Use only listed hose assemblies to dispense fuel. Hose length at automotive fuel dispensing facilities should not exceed 18 ft. (5.5 m). Where hose length at marine motor fuel dispensing facilities exceeds 18 ft. (5.5 m), secure the hose to protect it from damage. Underwriters Laboratories UL 330, Standard for Safety
Safe Work Procedure Fuel Storage & Handling
Safe Work Procedure Fuel Storage & Handling The information contained in this document is provided for use by Fuelco Pty Ltd as a guide where a safe work procedure for the safe storage and handling of fuel does not exist. Please check local requirements and OH&S regulations before using or implementing. Sequence Hazards Process Precautions
A Field Guide to Fuel Handling, Transportation & Storage
A Field Guide to Fuel Handling, Transportation & Storage 3rd Edition q Use an electric fuel pump when dispensing from a drum. When an electric fuel pump is not available or not practical, use a manual pump. Always store and secure the fuel hose above the drum to prevent siphoning. q Ensure that dispensing procedures are clearly outlined and
Retail Gasoline Dispensing Safety Act and Regulations
N.J.S.A. 34:3A 4 et seq. RETAIL GASOLINE DISPENSING SAFETY 34:3A 4. Findings, declarations The Legislature finds and declares that: a. Because of the fire hazards directly associated with dispensing fuel, it is in the public interest that gasoline station operators have the control needed over that activity to ensure compliance with appropriate safety procedures, including turning off vehicle
A Safety Checklist for Fuel Dispensers at Filling Stations
Inspect all dispenser hoses for flattened areas, cuts, leakages and cracks. If you find a damaged hose, repair or replace it—as deemed necessary. Check the Fuel Nozzle Safety Features. Fuel nozzles are part of a fuel dispensing machine. They come equipped with essential safety features to prevent accidental spills and breakaway damages.
STANDARD SAFETY PROCEDURES PRIST RECEIVING AND
STANDARD SAFETY PROCEDURES PRIST RECEIVING AND DISPENSING OBJECTIVE: To provide a safe environment for the ASIG employees, who are tasked with receiving/transferring Prist and to ensure the delivery of pure fuel system icing inhibitor into aircraft. ASIG will meet the minimum requirement for that airline/General Aviation
Diesel Dispensing Tanks & Diesel Fuel Storage Tanks Safe
Safe T Tank offers UL 142 listed, above ground diesel fuel storage tanks and bio diesel dispensing tanks that can accommodate between 50 2,000 gallons.
F&AM, Engineering Safety & Health Tech Tips
before dispensing fuel. Ground and/or bond all containers before opening and dispensing fuel. Physically touch the outside of containers, grounds, and bond wires to bleed excess charges off your body. Touch the outside of metal and plastic containers with the fill nozzle before opening and dispensing fuel. Use labeled safety containers with anti
Technical Training & Documentation Censtar
North America Technical Training Gilbarco provides a wide range of expert resources to ensure outstanding field support for you. We have an extensive offering of classes, certified trainers, and video and traditional documentation.
Fuel Safety Signs from
wording: warning gasoline health and safety extremely flammable, vapors may explode harmful or fatal if swallowed long term exposure to vapors has caused cancer in laboratory animals keep face away from nozzle while filling keep nozzle away from eyes and skin never syphon by mouth don't overfill tank don't allow individuals under license age to use pump for use as a motor fuel only
Fuel Dispensing Troubleshooting Husky
A coax spout nozzle will have fuel that drains from the vapor collection holes near the end of the spout. Make sure there is a constant flow of fuel coming out. With a constant fuel flow verified, watch the gallons meter for a minimum of one minute to about five minutes and if the meter creeps install a working nozzle and repeat the procedure.
AC 150/5230 4B, Aircraft Fuel Storage, Handling and
Attn: Fuel Safety Training 800 Independence Ave SW AAS 300, Room 618 Washington DC 20591 7. Principal Changes. This AC contains: a. New Chapter 1, Standards and Resources for Procedures on Fuel Storage, Handling, and Dispensing b. New Chapter 2, Fuel Safety Training c. New Chapter 3, Supervisors Training Course d.
Important Guidelines for Installing PetroClear Fuel
Although PetroClear fuel dispenser filters are designed to be installed quickly and easily, it is very important that operators and technicians maintain safe handling procedures at all times. Failure to comply with safety procedures can result in a fire, serious injury or death.
GUIDELINES FOR CONSTRUCTION OF PETROL STATIONS
GUIDELINES FOR CONSTRUCTION OF PETROL STATIONS 1. MINIMUM STANDARD REQUIREMENTS OF A PETROL FILLING STATION A petrol filling station should have at least: One underground storage tank for each petroleum product sold at the station with a minimum capacity of 5 m3 One digital dispensing pump (two way) for each petroleum product sold at the
FUEL TRANSFER (DELIVERY) OVERVIEW Petro Analytical
the product and familiar with formal written procedures for controlling any spill that may occur. CLIENT FUEL DELIVERY STANDARD OPERATING PROCEDURES . PROCEDURE. Bulk diesel product delivery to either aboveground or underground fuel tank . PURPOSE. To assure the safe and proper transfer of diesel . SCOPE
API Staying Safe at the Pump
Staying Safe at the Pump. Static electricity related incidents at retail gasoline outlets are extremely unusual, but the potential for them to happen appears to be the highest during cool or cold and dry climate conditions. In rare circumstances, these static related incidents have resulted in a brief flash fire occurring at the fill point.
Fuel handling and storage. Occupational
Liquid fuel dispensing devices shall be provided with an easily accessible and clearly identified shut off device, such as a switch or circuit breaker, to shut off the power in an emergency. (a)(9) Liquid fuel dispensing devices, such as pumps, shall be mounted either on a concrete island or be otherwise protected against collision damage.
WAYNE OVATION INSTALLATION & OPERATION MANUAL
View and Download Wayne Ovation installation & operation manual online. Ovation Dispenser pdf manual download. Also for: Ovation series, Ovation r13,
NFPA 30A: Code for Motor Fuel Dispensing Facilities and
1.1* Scope. A.1.1 This code is recommended for use as the basis for legal regulations. Its provisions are intended to reduce the hazards of motor fuels to a degree consistent with reasonable public safety, without undue interference with public convenience and necessity. Thus, compliance with this code does not eliminate all hazards in the use of these fuels.
Standard Operating Procedure: Vehicle Fueling
Standard Operating Procedure: Vehicle Fueling . I. Introduction and Purpose. Vehicle and equipment fueling procedures and practices are designed to minimize pollution of surface or ground waters. Understanding the procedures for delivering fuel into vehicles, mobile fuel tanks, and storage tanks is critical for this purpose.
Vehicle and Equipment Re fueling Safe Practices and
Vehicle and Equipment Re fueling Safe Practices and Pollution Prevention Protocols Overfills, spills, and leaks that occur during vehicle and equipment re fueling at the the procedures described below must be adhered to when refueling to of the fuel dispensers per National Safety Council guidelines and National Fire Protection
Standard Operating Procedures Dispensing Rx Advisor
Standard Operating Procedures Dispensing . Receiving Prescriptions Purpose To ensure a high standard of customer service and the safe, secure, and efficient handling of prescriptions received at the dispensary. Scope . The procedure covers the receipt of NHS and private prescriptions presented at the dispensary. Procedure / Process . 1
Test Procedures for Inspecting Fuel Dispensers
Test Procedures for Inspecting Fuel Dispensers (90 liters/min or less) 1. Standards 2. Device Use 3. Visual Exam 4. Performance 5. Sealing Physical Standards Physical Standards Certified Within Prescribed Period (R56) Test Measures must be certified every 1 year Provers with valves must be certified every 4 years (some 2 years)
Petrol Stations Health and Safety Authority
Fuel and oil spillages on the forecourt can present a slipping hazard Supplies of industrial salt mixed with fine gravel should be kept and spread on the forecourt during icy conditions and also used promptly to absorb and clean up any fuel or oil spill.
Fuel Dispensing Procedure Freedom Aviation
Fuel Dispensing Procedure. All users of the FAS fuel dispensing system at 14 Wing Greenwood shall be trained on this policy prior to operation of it. We realize pilots are trained in safe aircraft fuelling procedures as part of their pilot training and this is additional Freedom Aviation site specific.
Civil Engineering Sector Labour Management Health and
Civil Engineering Sector Labour Management Health and Safety Committee July 2008 The dispensing of fuel from a highway tank or mobile refuelling tank to a motor vehicle with hoisting equipment in accordance with normal safety procedures.
NFPA 30A, Code for Motor Fuel Dispensing Facilities and
Reduce risks through compliance with the 2018 edition of NFPA 30A, Code for Motor Fuel Dispensing Facilities and Repair Garages, presenting the latest rules for fuel storage and piping, fuel dispensing systems, and operating procedures for retail fuel dispensing, marine fuel dispensing, and fleet vehicle fuel dispensing. NFPA 30A also covers
Safe Fueling Procedures Indiana Constructors, Inc.
SAFE FUELING PROCEDURES Use only safety cans or other approved portable fuel containers to transport or transfer fuel. Unapproved containers can leak, spill fuel or rupture. Never dispense fuel into a can or other portable container while it is sitting in your vehicle or truck bed. If you have a fuel spill:
Aircraft Systems: Aircraft Fueling and Defueling Procedures
Safety procedures to be followed when perform fueling and defueling. Sequence in defueling an aircraft’s fuel tanks avoids structural damage. Follow the manufacturer’s procedure for defueling the aircraft. What to do with the fuel coming out of a tank depends on a few factors.
Civil Engineering Sector Labour Management Health and
Procedure: Procedure for the Handling of Fuel on Construction Sites All other terms as defined in the LFHC, Section 1.4. 4.0 RESPONSIBILITIES 4.1 It is the primary responsibility of the Supervisor(s) to see to it that all fuel handling and dispensing is done in a safe and proper manner in accordance with this procedure.
Guidelines for the Safe Operation and Maintenance of Marinas
4.1 The fuel dispensing area should be located a sufficient distance from other structures to allow adequate room for safe ingress and egress of craft to be fueled. Dispensing units should be at least 25 feet from any activity not associated with the handling of fuel. 4.2 Approved dispensing units, with or without integral pumps, should always
Refuelling safety Housing Public Works
materials (e.g. the fuel and the metal fuel filler neck). When the static electricity discharges, it produces sparks which can ignite the fuel vapours. The fuel dispensing pumps found at service stations and the fuel filler necks of motor vehicles are earthed to minimize and control the static electricity produced during normal vehicle refuelling.
DIESEL TRANSPORT, STORAGE AND REFUELLING
understanding the safety requirements for diesel transport, storage and refuelling in underground mines, and to provide guidance, at the practical level, on essential design aspects and operating practices. It is not a comprehensive technical document and does not deal in detail with specific tasks or operating procedures.
LIQUID FUEL DISPENSER & PUMP SERVICE MANUAL
LIQUID FUEL DISPENSER & PUMP SERVICE MANUAL Liquid Fuel Dispenser & Pump Service Manual Version 1.0.1 explain all servicing procedures, warnings, and safety precautions as clearly and completely as possible. However, due to the range of operating Compac liquid fuel dispensers are designed to meter petrol and diesel under the
YOUR PETROLEUM STORAGE TANK FACILITY INSPECTION
YOUR PETROLEUM STORAGE TANK FACILITY INSPECTION GUIDE HOW WELL DO YOU KNOW YOUR PETROLEUM STORAGE AND DISTRIBUTION SYSTEM? This publication can be made available in large print, tape cassette or braille by request.
Bonding and Grounding of Flammable Liquids Quick Tips
The process of bonding and grounding can be defined as providing an electrically conductive pathway between a dispensing container, a receiving container and an earth ground. This pathway helps eliminate the buildup of static electricity by allowing it to safely dissipate into the ground. Both the National Fire Protection Association (NFPA) and the Occupational Safety and Health Administration
Kerosene Safety Signs from
Kerosene Signs and Labels. Wherever Kerosene is stored or used, safety is always a concern. Fortunately, posting signs about Kerosene reminds everyone to be cautious and follow established safety procedures. Kerosene signs and labels from can help prevent costly injuries and downtime. They're available in a variety of
Safe Fueling Procedures Indiana Constructors, Inc.
Use only safety cans or other approved portable fuel containers to transport or transfer fuel. Unapproved containers can leak, spill fuel or rupture. Never dispense fuel into a can or other portable container while it is sitting in your vehicle or truck bed. If you have a fuel spill: Clean it up immediately using the appropriate spill kit.